It looks like underextrusion at speed. It might be a clog or you might want to try a higher hotend temperature. PLA can have inconsistent ideal temperatures even with the same brand due to different colors and additives between batches and 185 is on the low side.

Right image, but under those each one below would also be wearing large pants covering each side of the subtree.

If 35° (or something close to it) is the slicer setting for overhang detection it likely changes the cooling/speed/flow settings. If that is the case you can set it to a lower detection value and maybe get better results or change the normal cooling/speed/flow to be closer so it isn’t as drastic of a change.

The biggest issue is that your corners are lifting from the bed during the print. Fixing this is usually a combination of making sure the bed is clean and adding a brim to increase adhesion. Maybe messing with temperature and cooling fan settings for the first few layers.

Second is things look a bit over extruded. This could just be due to the corner issue though so fix that before any other changes.

There is also SMS passive reading using LEO intercept. Hacked police email accounts are used to gain access to carrier systems where they use “imminent threat” no warrant lookups to pull the SMS in real time.

SMS is a terrible form of 2FA, better than none but not by much.

Your experience may depend on which distro you use and how you install things. If you use a distro with a stable upgrade path such as Debian and stick to system packages there should be almost no issues with upgrades. If you use external installers or install from source you may experience issues depending on how the installer works.

For anything complex these days I’d recommend going with containers that way the application and the OS can be upgraded independently. It also makes producing a working copy of your production system for testing a trivial task.

You might also try running a few leveling probes in a row to check the repeatability of the measurements. It’s possible that something is messing with the ability to make good measurements (unstable power feed, heat warp, probe binding, etc).

I’n Windows it is not stored in a keyring but instead in the registry. This has basically the same security threat model as a local key file.

The ssh-agent on Linux will do what you want with effectively the same security. The biggest difference being that it doesn’t run as a system service but instead runs in userspace which can make it easier to dump memory. There are some other agent services out there with additional security options but they don’t change the threat model much.

My memory of the cp command is that attributes such as file times were transferred at the last step. I think this would make rsync safe in most situations where a system crash wasn’t involved.

I think I remember running into that as well but for whatever reason I couldn’t get accelerated-x working with the opengl libraries I was using for school. Likely the issue was just a lack of understanding on my part as I don’t think I had a good grasp of the Linux library loader until well after I graduated.

I’ve had a system in the late 90s with a 3dfx voodoo card. Also had a laptop with a SIS card from the early 2000 era.

The voodoo card was THE card to have it it’s day (mine was an older second hand system though). The SIS card… for some reason they decided that standard VESA mode probing wasn’t a thing they supported and would hardware crash when that API was used. I eventually got it working in Linux after patching xfree86 to not attempt probing when loading the VESA driver.

You may want to try hotter too if you haven’t yet. Printing faster can sometimes require a bit of extra heat and too low can cause a different kind of stringing.

QEMU supports either spice, vnc or sdl graphics output. If you want to copy/paste you need to use spice and install the spice agent on the VM.

My steam deck also unlinks family libraries with almost every os update. It might be an issue of overzealous hardware validation but it could also just be a bug.

It’s very likely that your disk is failing.

dd if=/path/to/file.mkv of=/new/file/path.mkv conv=noerror,sync bs=4k

Should give you a file with just the damaged bits missing.

PTSD from the days long ago when X11 error log would fill up the disk when certain applications were used.

The underutilized post pre increment operator.

Are they on a local disk? Thunar doesn’t render any thumbnails for remote storage by default.

They fail because you can’t trust a machine that an adversary has in their physical possession.

Software running on an untrusted computer can have code and memory injected or modified without modifying the executable files. Binary executable files are by necessity readable and someone with enough time can parse through them to fully deobfuscate and figure out what they are doing. Anti-anti-cheat systems basically perform the same code as the anti-cheat but slightly modify the result to hide the cheating. This can be done either by code swapping in the anti-cheat or at a higher level. If the anti-cheat system is looking at which processes are running then have the system feed it the real list of processes with the cheat processes removed… etc.

Trusted computing requires hardware level monitoring, validated certificates, and zero vulnerabilities since the time the certificate was provisioned. In addition, current technology would also require those base certificates to be regularly rotated and device decertified if it didn’t rotate in time to prevent physical offline hardware attacks on the certificate data. Even game consoles don’t have this level of platform trust and are often physically modified to enable cheating/piracy.

The only successful way to prevent most cheating is to run the simulation entirely server-side and then only send data to each client according to what they should know. Even then you won’t be able to prevent assisted cheating like aim-bots or texture replacements.

When rsync copying the active root I like to bind mount / to /mnt/root_fs first. This avoids the issue with needing to exclude folders with sub-mounts and will expose files to copy that might be hidden by the mounts.