It did alright, don’t think I saw that many obvious cheaters in BF1. BF5 would occasionally have obvious cheaters, but I would hope they get banned eventually just because it’s over the top (shooting people through walls, infinite ammo, perfect aim). Difficult to say with more subtle cheats, but I suppose if they’re indistinguishable from players who are just good at the game then I think most people won’t ever notice.

On the flip side I got permabanned from multiplayer in BF5 after EA falsely accused me of cheating, though I suppose that could’ve happened with any kind of anti-cheat, and could’ve been fixed by having half-competent support.

I think FairFight is the old anti-cheat, which at least used to be server side only.

Unfortunately most Battlefield games worked fine with Wine/Proton for years since EA used server side AC, so they already have our money.

I’ve never got my Vive to work well in Linux, even though I’m using X which supposedly still is better for gaming that Wayland.

What is the solution?

My guess is that Microsoft wants provide some kind of kernel level anti-cheat, possibly directly integrated with directx, and it will use cryptography which will make it impossible to emulate with Wine/Proton.

Did you follow some guide when replacing the nozzle and bowden tube? Did you hot tighten it when putting them back?

What speed are you printing at, which you think is too slow? What’s your acceleration?

It’s a myth that capricorn tubing is better in any way

I’d call it “successful marketing” :) But yeah, they’re really managed to convince a lot of people that it has near magical properties, and I’ve seen a lot of random people recommend it to others for all sorts of issues.

So sad that they didn’t fix the AC until the game had been around for years, I would’ve loved to play it in the beginning when the player skill was more varied. Tried to get into it when Linux was allowed but it seemed like mostly the try-hards were still playing. Had some good games but it was a bit too sweaty for my friends at times.

I tried playing it through Wine during season 2 or 3, the game worked flawlessly but you would get kicked after 1-5 minutes due to missing AC.

The first game was named Battlefield 1942, so technically there hasn’t been a “1” in the series before this :) It came out in 2016 so it’s not really new, but I bought it last year and played it on Linux for a few hours with friends, and it still has an active player base.

Have they stated that they’re going to support Linux or at least Proton/Wine? I did a quick search on the game’s Steam forum and it sounded like it doesn’t work currently.

Ahh, now I get it :P

Nope, Norwegian company until they were bought by Chinese investors a few years ago. They did have a lot of developers in Sweden and Poland though.

My 4 last employers have used desktop Linux to some extent:

• Ericsson (Swedish telecoms), default was to have a Windows laptop with X server (Citrix?) but a few of us were lucky enough to get a Linux laptop.
• Vector (German automotive), Linux dev. environment in a VM on Windows laptops.
• Opera Software (Norwegian web browser), first day I was given a stack of components and told to assemble my PC and then install my Linux distribution of choice.
• And a smaller company, which shall remain unnamed, also used Windows laptops with Linux dev. env. in VM.

Sure most of it was on top of Windows, but if you fullscreen it you can barely tell the difference :)

It sounds like bed adhesion might have got worse, perhaps you have touched the print surface with your fingers while removing prints? You could try removing the plate and washing it with warm water and soap. Some people use IPA but if you do then you need to make sure you really wipe it clean before it evaporates, otherwise the dissolved fats will stay on the bed. If your bed has some kind of anti-stick coating I think there’s also a risk that you damage if you use stronger solvents.

As for warping in general it could be an indication that your flow rate is exceeding your melting capacity. If you have an all metal hotend you could try printing at higher temp, if not then try reducing print speed instead.

My first couple of computers had AmigaOS and even from the start Windows felt like complete garbage in comparison, but eventually I had to buy a PC to keep up with the times. After that I kept looking for alternative OS:es, tried Linux dual booting but kept going back to Windows since all the programs and hardware I needed to use required it. When I finally decided to go full time Linux, some time between 2005 and 2010, it was because I felt like I was just wasting my life in front of the computer every day. With Windows it was too easy to fire up some game when I had nothing else to do, and at that time there were barely any games for Linux so it removed that temptation. But that has ofc. changed now and pretty much all Windows games work equally well on Linux :)

Ahh, I thought you meant you had a 0.2mm nozzle, but now I see you probably meant layer height.

Moisture absorbtion is rarely a problem with PLA, but hopefully dehydration won’t hurt, as long as you don’t accidentally overheat it and it deforms. I’ve left rolls of PLA out in the open for 6 months without noticing any deterioration. Both your filaments used to print fine, and then the oozing spontaneously started with both of them?

2mm retraction should be more than enough for a direct drive extruder.

The only certification I have is from the Kansas City Barbeque Society, allowing me to act as a judge in BBQ competitions.

Things are probably different nowadays, but at least 15-25 years ago you could just apply for IT jobs and if someone lied about their skills it would hopefully show during the technical interviews. I don’t know if that counts as getting in very early.

What filament and other slicer settings? Could be too hot. Could be retraction settings. Did the oozing start when you switched nozzles? If it’s a cheap Amazon nozzle it might be faulty and have a different diameter than advertised. Did you follow the correct procedure with hot tightening when switching nozzles? If not, you might have got molten filament in between the nozzle and the heat break.

Easiest GUI toolkit I’ve used was NiceGUI. The end result is a web app but the python code you write is extremely simple, and it felt very logical to me.

Probably a joke, since there’s always someone commenting that the item isn’t food safe whenever a model for something food related.