Fwiw I used to daily an x210 and then an x230 in IT and pretty frequently typed with one hand while carrying with another without the weight bugging me but your mileage may vary.

You can definitely send them flying and not damage them my coworker launched theirs across the office and the bezel just snapped back together.

I have a T480 now since I do more dev work and needed a slightly bigger keyboard/screen and it’s phenomenal with Qubes and 48gb of memory on the quad core i5. Love the ease to repair I just swapped a motherboard on it in around 30 minutes and was back up and running

I just use nextcloud as a target for backups (Aegis, Signal, QkSMS). Apps such as KeePassDX I have load the file via nextcloud. My contacts and calendar go through it as well, photos are just set to auto upload along with a few other directories.

As for the home screen layouts, I just take screenshots once I have it how I like and try to remember to take them again if I change stuff.

It’s not a full backup but I’m back up and running fairly quickly (Pixel 5A died on me 3 times in under a one year lifespan per device).

I don’t own Prusas but I migrated from super slicer to prusaslicer and being able to cut models and add locating pegs easily is such a game changer for larger parts

Me after getting those dumbass Canary cameras that cost $200 a piece then they completely wrecked the free tier then started giving them away for free to get more subscribers.

Wyze cams with wz_mini_hacks firmware offline in a VLAN with Frigate and Home assistant from here on out!

I would never go back from qubes. VirtualGL seems promising for the hardware accelerated apps and GPU passthrough for a gaming VM is insane

Adjust your thumbstick deadzone if you haven’t yet, the default is super high I run mine at 2000 and it made them feel a lot more responsive.

I like to have gyro aim only when I touch the right track pad, playing through Halo MCC right now and it’s fantastic, especially using turrets with gyro. Thumbstick for general movement, track pad and gyro for combat.

We’re using the grunt party skull where you get the party sounds and streamers when you headshot them and I’m able to pretty consistently nail them after a few missions with that setup.

Not using any auto aim

You probably unknowingly break multiple laws a day settle down

Yeah and whatever you do definitely don’t use Jellyseerr for Jellyfin setups or Overseerr for Plex setups

Do you have any of their doorbells? I went back to a physical doorbell button with home assistants sky connect dongle linked up to a motion sensor at the door just so I know when someone’s there but would love to get a camera up there that isn’t some ring bs

These cameras work very well with the wz_mini_hacks firmware completely cut off from the internet. I’m using frigate and home assistant for notifying and it’s honestly way better than the wyze app ever was.

I’m running frigate on a Lenovo m900 with the coral USB accelerator and my CPU usage is super low so you could probably get away with the Pi4!

I remember watching the trailer for that game over and over and over, the first one you could go outside

Wow he must’ve struck a nerve with you to get this reply

You’ve insulted my entire existence I challenge you to a duel

I sure hope so, I love my steam controller but it really could benefit from dual thumbsticks

Yep and reddit is slowly closing themselves off, I wouldn’t doubt you eventually have to be logged in to even view anything.

Forums are still around but it’s usually just the older established ones (I’m on stangnet.com and corral.net regularly but they’re car related so lots of technical info). Everything new either went Reddit or Discord it feels like and I’ll never install Discord.

I think Jellyfin started a forum post reddit but I haven’t gone looking yet for that one.

Information is absolutely getting harder to find online and if archive.org goes down we’re really screwed

I don’t think your particular case would have any creep as it’s not mechanically leveraged in any real way.

If you were to print something like a cupholder for a stroller or bike where it’s holding something up with some weight while in the heat is where you would notice it especially with repeated impact. Most likely wouldn’t outright fail but under constant load you would notice it starting to bend a little. That said you can absolutely over engineer it to prevent that rather than switching materials which can be a huge pain depending on the printer.

I did my hydroponic tower in PETG but it honestly would’ve been ok in PLA since it’s just a static fixture. I’ve had a PLA badge on my car for 3 years in 110+ summers and similar to you I’ve only noticed fading on the raised white lettering.

I’m on the 5A now and my wife has a 7, her 7 has the screen randomly freak out where you can’t even turn it on or reset (holding power will make it vibrate after about a second preventing the hold to reset). Just have to mess with it until you can get in and hit restart then it’s fine for another week or two usually.

The 5A is fantastic until it abruptly dies which has happened to me twice now (both times while sitting with it in my hand). If they didn’t have screen and motherboard issues I would absolutely run this phone into the ground since it’s a great experience with GrapheneOS, has a headphones jack, and has the rear facing fingerprint sensor.

I can’t speak to the 6 but I know some people didn’t like them after the 5 since it switched to tensor

I started with openscad and moved to freecad. Freecad is powerful but definitely not perfect but it has suited my needs fairly well.

I’m still a holdout for superslicer but I did migrate my profiles to PrusaSlicer for those sweet organic supports.

Using sonixd for desktop and finamp for mobile through my Jellyfin server and really liking it.

I did have to make a separate Jellyfin account for my music since I didn’t want music showing up on the Jellyfin TV apps cluttering it up but not bad overall!

Finamp doesn’t track new items in a playlist marked for offline play which is my main gripe atm.

I just used a buck converter and a USB pigtail for mine so it still plugs into the pi where the power cable used to it’s just running off the Ender 3s power supply. They were fairly cheap on Amazon something like $6 for a pack

The only cables you really see for my printer are the short USB connecting the Pi to the SKR on the back, and the power supply cable. The rest is hidden or inside cable chains.

Definitely made moving the printer easier and much less of an eyesore of wiring.